LPLDD-5A-12V-TP

One channel 5A 7,5-12V laser diode driver with thermal protection. Based on many inquiries from customers, this version of the LPLDD-5A-12V driver is equipped with thermal protection which switches off the laser diode circuit if the temperature exceeds 45 degrees of Celsius. Thermal sensor is included. Additional LEDs signalize the current status of the driver. 

Reference: 001288

EAN13: 5902693110767

Manufacturer:

Available quantity: 87 Items

    $45.00 tax excl.

    Product Description

    New version of classic laser diode driver with thermal protection ensures proper work of the laser diode and protects it from overheating. Basic driver for powering laser diodes with the option to adjust maximum output current in the range of 0-5 A, and to modulate the current flowing through the diode with frequency up to 100kHz. The exemplary test with the 100kHz square-wave input signal modulation is shown below.

    LPLDD5A-12V-TP driver is capable to power literally every laser diode available on the market up to 5W - 405 nm, 445 nm, 520 nm, 638 nm, 650 nm, 808 nm, 980 nm. The examples of diodes are: 1W 445 nm, 3,5W 445 nm, 700mW 635 nm, 200mW 808 nm, 1W 808 nm, 5W 808 nm, 1W 520nm.

     

    Thermal Protection

    This driver has thermal protection system which protect laser diode from overheating.

    • In case of normal operation, when a thermistor measures the temperature of a laser unit below 40 degrees of Celsius, the green LED is ON.  Overheat pin status:  High, output 5VDC.
    • When the temperature measured by the thermistor reaches 40 degrees Celsius, the red LED starts blinking. Green LED is still ON. Overheat pin status:  High, output 5VDC.
    • When the temperature measured by a thermistor reaches 45 degrees Celsius, the red LED is ON, and the laser diode driver switches off. Overheat pin status:  Low, output 0VDC. The laser diode driver will get to normal operation when the temperature measured by a thermistor is lower than 40 degrees.
    • Two blinking LEDs means that there is no connection between the laser diode driver and a thermistor or the connection was temporarily lost.  When the connection established - reset the driver. To reset the driver, disconnect and connect the power supply of the driver.

    Electrical Protection

    • Driver’s power input is protected by 12V transient-voltage-suppression diode.
    • Modulation input of the driver is protected by 5V1 Zener diode. Nevertheless, one should not use modulation voltage higher than 5V.
    • The output of the driver is protected by the Schottky diode which doesn't allow the reverse voltage to appear as well protects from ESD.

     

    Recommendations and requirements

    The supply voltage should always be set higher than or equal to 3,3V. The minimum supply voltage for other situations is given by the formula:

    Vin = 0,2* I + Vd

    Vin is input voltage

    Vd is diode working voltage

    I - operating current

    Modulation input can be used as TTL input with its logic levels of 0V and 5V or as an analog input. Analog modulation means that by using 2,5 V on ANG input you get 50% of the preset (via potentiometer) current at the output, analogically by using 4 V you get 80% of the preset current value. 0

    For powering the driver, we recommend the use a cable with cross-section of: 0.1* I [mm2], where I operating current.

    Depending on used laser diode and PSU, you should assure proper cooling of the MOSFET transistor. The MOSFET must be isolated from the heatsink/plate with silicon pad as well as plastic sleeve. Short circuit between MOSFET and heatsink/plate may damage the driver and can be dangerous for the Laser Diode.

     

    Exemplary Test

    Test done using:

    •          6W NUBM44 laser diode
    •          15cm long 0.35mm2 wires
    •          12V input voltage
    •          80x80x20 heatsink on power MOSFET





    Technical Data

    Dimensions34x26x24
    Input Voltage7,5 - 12 V
    Max Ouptut Current5 A
    Max. Modulation Frequency100 kHz
    Max. Power Dissipation15W
    Modulation Input Voltage Range0 - 5 V
    Modulation TypeAnalog
    Pre-Set Current Setting2000 mA
    Softstart Time1 ms
    Temperature Sensor Type10k NTC thermistor
    Rise Timeless than 1.5µs
    Fall Timeless than 1.5µs
    Noise and Ripple (RMS)12.5 mA
    Minimum Current (3% Noise)500 mA