In order to improve the quality of the services we use cookies. By staying on the site, you agree to the use of this technology. See more on Privacy policy.

Register to receive additional 3% discount

5kHz 3-24V 60A HPLDD

Availability: (5 items)

Description Details Comments

Click to download user manual


This is a professional driver dedicated for high power infra red laser diodes. This is slower version of the driver. It is possible to modulate the current with frequency up to 5kHz. If you need higher modulation frequency please find my other auction with 20kHz version of a driver. It can work with 20, 40, and 60W CS-mount 808nm, 940nm and 980nm laser diodes as also with other similar diodes.

With this driver you can power one diode or several diodes in series as also one diode stack which requires higher working voltages. In recommendation section there is a formula for maximum input voltage.

Separate laser diode supply voltage input and logic input voltage allows to minimize the switch-on resistance of a power MOSFET. Inner layer of the heatsink is made of copper and helps in fast heat transmission. The outer body of a heatsink, made of alluminium, is isolated from all signals on the driver, including GND signal. It allows to mount the driver directly to the metal components in case of additional cooling needed.

Analog input allows for the modulation of the current flowing through the diode up to 5 kHz. Two potentiometers are used to set the values of maximum diode current and bias current. On the other auction you can find version which is able to modulate the current with frequency up to 20kHz

Attached to the driver is connector and pins which are used to power and control the unit as also the M5 stainless steel screws.

We can also supply the proper power supply unit. Please feel free to contact us with any questions.

 

Recommendations and requirements

Supply voltage range depends on the quantity of laser diodes used in series. For one laser diode which operating voltage is around 2V, maximum diode input voltage should not exceed 5V. For two diodes which operating voltage is around 4V, maximum diode input is 7V and so on. Therefore the maximum input voltage is given by the formula:

VCC DIODE MAX = (Number of diodes in series) X (Each diode operating voltage) + 3V

Always power the logic with 12V before powering up the diode line. Because GND of the diode line and GND of the logic input are connected in the driver, always remember to connect GND of the diode line directly to the GND of a PSU.

Always use high quality power supply unit with low ripple voltage. Adding large capacitor at the driver input is strongly recommended, but it depends on PSU, wires cross-section and their length. The capacitor used during the tests was 10000uF 25V.

You should be very careful not to cause short circuit between the + (VCC) of the power supply and -(GND) of the logic input or monitor input, as a thin GND logic paths can be irreparably damaged.

Modulation input can be used as TTL input with its logic levels of 0V and 5V or as an analog input. Analog modulation means that by using 2,5 V on ANG input you get 50% output power, analogically by using 4 V you get 80% output power, etc.

We recommend the use of power cables with cross-section of at least 4 mm2


Protection

Due to high current flowing trough the paths we minimalized the voltage drop on the driver and there is no reverse polarity protection. We strongly recommend using LASORB protection device mounted close to the diode.

The driver's body is isolated from all signals of the driver and can be mounted directly to the metal heatsinks or other metal parts.

The analog input is protected by a 5V1 Zener diode on occasion there appears the voltage higher than 5V. Despite everything, this input should not be used with higher voltages.



Features:
Driver dimensions (LxWxH mm) 95x50x30
Modulation frequency (kHz) 5
Modulation voltage range (V) 0 - 5
Softstart (ms) 2000
Maximum diode current (A) 60
Laser diode suppply voltage (V) 3-24
Transistor type High power N-MOSFET
Maximum bias current (A) 20
Logic supply voltage (V) 12
Connector material Cooper
Power connector screws Stainless steel M5
Inner heatsink material Cooper plate
Outer heatsink material Alluminium
Isolated from all signals heatsink Yes
Mounting holes raster (mm) 85x40
Mounting hole diameter (mm) 5,5
Maximum power dissipation (W) 200
Current monitor 10 mV / 1 A
Current set by default (A) 10
Internal part no 001136
Driver dimensions (LxWxH mm) 95x50x30
Modulation frequency (kHz) 5
Modulation voltage range (V) 0 - 5
Softstart (ms) 2000
Maximum diode current (A) 60
Laser diode suppply voltage (V) 3-24
Transistor type High power N-MOSFET
Maximum bias current (A) 20
Logic supply voltage (V) 12
Connector material Cooper
Power connector screws Stainless steel M5
Inner heatsink material Cooper plate
Outer heatsink material Alluminium
Isolated from all signals heatsink Yes
Mounting holes raster (mm) 85x40
Mounting hole diameter (mm) 5,5
Maximum power dissipation (W) 200
Current monitor 10 mV / 1 A
Current set by default (A) 10
Internal part no 001136

Write your review

5kHz 3-24V 60A HPLDD

5kHz 3-24V 60A HPLDD

This is a professional driver dedicated for high power infra red laser diodes.

Write your review

$ 295.00

plus1

  • Remove this product from my favorites
  • Add this product to my favorites
  • Share on Facebook!
  • eBay TomorrowsSystem profile eBay TomorrowsSystem reviews
    eBay showProfile on page